Songhan Plastic Technology Co.,Ltd.

Resinlab® EP1199 Black Unfilled Epoxy Adhesive

Category Polymer , Adhesive , Thermoset , Epoxy , Epoxy Adhesive
Manufacturer Resinlab®
Trade Name
Port Ningbo port,China
Trade Terms FOB, CFR, CIF
Payment Terms L/C, T/T, Western Union
Download PDF Resinlab® EP1199 Black Unfilled Epoxy Adhesive.pdf
  Online Service   lookpolymers   27660005
Material Notes:
Resinlab™ EP1199 Black is a two part unfilled epoxy adhesive designed for bonding of metals, ceramics and most plastics. This product gives good resistance to water, salt spray, inorganic acids and bases and most organic solvents. This product gives better water and temperature resistance than standard 5 minute epoxy. It was especially formulated to a 1:1 mix ratio for use in either MMD equipment or side by side dual cartridges for easy dispensing. A handling cure is normally achieved at room temperature within 30 - 60 minutes with full cure in 24 hours. An elevated temperature cure schedule can be used to reach final properties quickly.Information Provided by Resinlab L.L.C., an Ellsworth Adhesives Company.
Physical Properties Metric English Comments
Specific Gravity 0.970 g/cc
0.970 g/cc
Part B; TM R050-16
1.06 g/cc
1.06 g/cc
Mixed; TM R050-16
1.16 g/cc
1.16 g/cc
Part A; TM R050-16
Water Absorption 0.28 %

@Time 86400 sec
0.28 %

@Time 24.0 hour
TM R050-35
Viscosity 3000 cP
3000 cP
Part B, RVT, #4, 2.5 rpm; TM R050-12
9000 cP
9000 cP
Mixed; TM R050-12
15000 cP
15000 cP
Part A, RVT, #5, 2.5 rpm; TM R050-12
Mechanical Properties Metric English Comments
Hardness, Shore D 80
TM R050-17
Tensile Strength at Break 27.6 MPa
4000 psi
TM R050-36
Tensile Strength, Ultimate 37.9 MPa
5500 psi
TM R050-36
Tensile Strength, Yield 24.1 MPa
3500 psi
TM R050-36
Elongation at Break 10 - 20 %
10 - 20 %
TM R050-36
Tensile Modulus 2.21 GPa
320 ksi
TM R050-36
Compressive Yield Strength 65.5 MPa
9500 psi
TM R050-38
Compressive Strength 138 MPa
20000 psi
Ultimate; TM R050-38
138 MPa
20000 psi
Break; TM R050-38
Compressive Modulus 2.76 GPa
400 ksi
TM R050-38
Adhesive Bond Strength 10.3 MPa
1500 psi
Lap shear; 2024 T3 Al Abraded / MEK Wipe; TM R050-37
Peel Strength 0.526 - 0.877 kN/m
3.00 - 5.00 pli
Thermal Properties Metric English Comments
CTE, linear 50.0 µm/m-°C
27.8 µin/in-°F
Maximum Service Temperature, Air 150 °C
302 °F
Minimum Service Temperature, Air -40.0 °C
-40.0 °F
Glass Transition Temp, Tg 82.0 °C
180 °F
TM R050-25
Electrical Properties Metric English Comments
Volume Resistivity 1.00e+15 ohm-cm
1.00e+15 ohm-cm
Dielectric Constant 3.0

@Frequency 100 Hz,
Temperature 25.0 °C

@Frequency 100 Hz,
Temperature 77.0 °F
Dielectric Strength 16.5 kV/mm
420 kV/in
Processing Properties Metric English Comments
Pot Life 8.0 - 12 min
8.0 - 12 min
Mass: 50g; TM R050-19
Descriptive Properties Value Comments
Color Black
Mix Ratio 1:1
Copyright © All Rights Reserved