Advanced Polymer Alloys DuraGrip™ DGR 6050 NC/BK Thermoplastic Elastomer (TPE)

Category	Polymer , Thermoplastic , Elastomer, TPE , Thermoplastic Olefinic Elastomer (TPO)
Manufacturer	APA - Advanced Polymer Alloys
Trade Name	DuraGrip™
Port	Ningbo port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Advanced Polymer Alloys DuraGrip™ DGR 6050 NC/BK Thermoplastic Elastomer (TPE).pdf
Price	EMAIL US sales@lookpolymers.com

Material Notes:

DuraGrip® DGR 6050 NC/BK are designed to be general purpose Thermoplastic Elastomers (TPE) that are easy to use in injection molding and extrusion processes. DGR 6050 NC/BK have an excellent soft touch feel, will bond to olefinics, and is available in FDA compliant formulations. DuraGrip® is not hygroscopic and under normal conditions does not require drying.Information provided by Advanced Polymer Alloys

Physical Properties	Metric	English	Comments
Specific Gravity	0.990 g/cc	0.990 g/cc	ASTM D471; ISO 2781
Viscosity	109000 cP @Shear Rate 300 1/s, Temperature 190 °C	109000 cP @Shear Rate 300 1/s, Temperature 374 °F	ASTM D3835
Linear Mold Shrinkage	0.014 cm/cm	0.014 in/in
	0.028 cm/cm	0.028 in/in
Linear Mold Shrinkage, Transverse	0.010 cm/cm	0.010 in/in
	0.013 cm/cm	0.013 in/in

Mechanical Properties	Metric	English	Comments
Hardness, Shore A	49	49	Time of 5 seconds; ASTM D2240; ISO 48
Tensile Strength, Ultimate	5.5080 MPa	798.87 psi	After 7 days at 70°C; ASTM D412 ISO 37
	5.8041 MPa	841.82 psi	After 7 days at 100oC; ASTM D412 ISO 37
	5.92 MPa	859 psi	ASTM D412; ISO 37
Elongation at Break	448 %	448 %	ASTM D412; ISO 37
	456.92 %	456.92 %	After 7 days at 70°C; ASTM D412 ISO 37
	470.4 %	470.4 %	After 7 days at 100°C; ASTM D412 ISO 37
Modulus of Elasticity	0.00199 GPa	0.289 ksi	After 7 days at 70°C; ASTM D412 ISO 37
	0.00214 GPa	0.310 ksi	After 7 days at 100°C; ASTM D412 ISO 37
100% Modulus	0.00205 GPa	0.298 ksi	ASTM D412; ISO 37
Graves Tear Strength	20.9 kN/m @Temperature 23.9 °C	119 pli @Temperature 75.0 °F	Die C; ASTM D624
Taber Abrasion, mg/1000 Cycles	70	70	Cs-17 Wheel, 1000 g Load; ASTM D3389
Compression Set	19 %	19 %	After 22 Hr at 75°F (24°C); ASTM D395; ISO 815
	41 % @Temperature 70.0 °C	41 % @Temperature 158 °F	22 hrs.; ASTM D395; ISO 815
	68 % @Temperature 100 °C	68 % @Temperature 212 °F	22 hrs.; ASTM D395; ISO 815
Tensile Set	9.0 %	9.0 %	100% Tension; ASTM D412

Thermal Properties	Metric	English	Comments
Brittleness Temperature	-67.8 °C	-90.0 °F	ASTM D746; ISO 812

Processing Properties	Metric	English	Comments
Processing Temperature	204 °C	400 °F
Rear Barrel Temperature	188 - 199 °C	370 - 390 °F
Middle Barrel Temperature	199 - 210 °C	390 - 410 °F
Front Barrel Temperature	216 - 227 °C	420 - 440 °F
Nozzle Temperature	204 - 221 °C	400 - 430 °F
Melt Temperature	199 - 221 °C	390 - 430 °F
Mold Temperature	43.3 - 54.4 °C	110 - 130 °F
Injection Pressure	1.03 - 3.45 MPa	150 - 500 psi
Cycle Time - Injection	0.50 - 2.0 sec	0.50 - 2.0 sec	boost
Screw Speed	25 - 100 rpm	25 - 100 rpm
Cure Time	0.167 - 0.333 min	0.00278 - 0.00556 hour	Cooling Time

Descriptive Properties	Value	Comments
Fluid Resistance - Volume Change, % (ASTM D471)	-12	After 7 Days in Water at 212°F (100°C)
	22	After 7 Days in ASTM Ref. Fuel No. B at 75°F (24°C)
	3	After 7 Days in ASTM Oil No.1 at 212°F (100°C)
	45	After 7 Days in IRM 903 Oil No.3 at 212°F (100°C)

Users viewing this material also viewed the following: