Advanced Polymer Alloys DuraGrip™ DGR 6030 NC/BK Thermoplastic Elastomer (TPE)

Category	Polymer , Thermoplastic , Elastomer, TPE , Thermoplastic Olefinic Elastomer (TPO)
Manufacturer	APA - Advanced Polymer Alloys
Trade Name	DuraGrip™
Port	Ningbo port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Advanced Polymer Alloys DuraGrip™ DGR 6030 NC/BK Thermoplastic Elastomer (TPE).pdf
Price	EMAIL US sales@lookpolymers.com
	Online Service lookpolymers 27660005

Material Notes:

DuraGrip® DGR 6030 NC/BK are designed to be general purpose Thermoplastic Elastomers (TPE) that are easy to use in injection molding and extrusion processes. DGR 6030 NC/BK have an excellent soft touch feel, will bond to olefinics, and are available in FDA compliant formulations. DuraGrip® is not hygroscopic and under normal conditions does not require drying.Information provided by Advanced Polymer Alloys

Physical Properties	Metric	English	Comments
Specific Gravity	0.990 g/cc	0.990 g/cc	ASTM D471; ISO 2781
Viscosity	129000 cP @Shear Rate 300 1/s, Temperature 190 °C	129000 cP @Shear Rate 300 1/s, Temperature 374 °F	ASTM D3835
Linear Mold Shrinkage	0.022 cm/cm @Thickness 3.17 mm	0.022 in/in @Thickness 0.125 in
	0.028 cm/cm @Thickness 1.59 mm	0.028 in/in @Thickness 0.0625 in
Linear Mold Shrinkage, Transverse	0.013 cm/cm @Thickness 1.59 mm	0.013 in/in @Thickness 0.0625 in
	0.016 cm/cm @Thickness 3.17 mm	0.016 in/in @Thickness 0.125 in

Mechanical Properties	Metric	English	Comments
Hardness, Shore A	33	33	Time of 5 seconds; ASTM D2240; ISO 48
Tensile Strength, Ultimate	3.9841 MPa	577.85 psi	After 7 days at 100oC; ASTM D412 ISO 37
	4.2468 MPa	615.95 psi	After 7 days at 70°C; ASTM D412 ISO 37
	4.38 MPa	635 psi	ASTM D412; ISO 37
Elongation at Break	485 %	485 %	After 7 days at 100°C; ASTM D412 ISO 37
	500 %	500 %	ASTM D412; ISO 37
	515 %	515 %	After 7 days at 70°C; ASTM D412 ISO 37
Modulus of Elasticity	0.000986 GPa	0.143 ksi	After 7 days at 70°C; ASTM D412 ISO 37
	0.00103 GPa	0.150 ksi	After 7 days at 100°C; ASTM D412 ISO 37
100% Modulus	0.00105 GPa	0.153 ksi	ASTM D412; ISO 37
Graves Tear Strength	14.2 kN/m @Temperature 23.9 °C	81.0 pli @Temperature 75.0 °F	Die C; ASTM D624
Taber Abrasion, mg/1000 Cycles	140	140	Cs-17 Wheel, 1000 g Load; ASTM D3389
Compression Set	10 %	10 %	After 22 Hr at 75°F (24°C); ASTM D395; ISO 815
	33 % @Temperature 70.0 °C	33 % @Temperature 158 °F	22 hrs.; ASTM D395; ISO 815
	53 % @Temperature 100 °C	53 % @Temperature 212 °F	22 hrs.; ASTM D395; ISO 815
Tensile Set	5.0 %	5.0 %	100% Tension; ASTM D412

Thermal Properties	Metric	English	Comments
Brittleness Temperature	-67.2 °C	-89.0 °F	ASTM D746; ISO 812

Processing Properties	Metric	English	Comments
Processing Temperature	204 °C	400 °F
Rear Barrel Temperature	188 - 199 °C	370 - 390 °F
Middle Barrel Temperature	199 - 210 °C	390 - 410 °F
Front Barrel Temperature	216 - 227 °C	420 - 440 °F
Nozzle Temperature	204 - 221 °C	400 - 430 °F
Melt Temperature	199 - 221 °C	390 - 430 °F
Mold Temperature	43.3 - 54.4 °C	110 - 130 °F
Injection Pressure	1.03 - 3.45 MPa	150 - 500 psi
Cycle Time - Injection	0.50 - 2.0 sec	0.50 - 2.0 sec	boost
Screw Speed	25 - 100 rpm	25 - 100 rpm
Cure Time	0.167 - 0.333 min	0.00278 - 0.00556 hour	Cooling Time

Descriptive Properties	Value	Comments
Fluid Resistance - Volume Change, % (ASTM D471)	22	After 7 Days in ASTM Ref. Fuel No. B at 75°F (24°C)
	6	After 7 Days in ASTM Oil No.1 at 212°F (100°C)
	70	After 7 Days in IRM 903 Oil No.3 at 212°F (100°C)
	-9	After 7 Days in Water at 212°F (100°C)

Users viewing this material also viewed the following: