Polymer Property : Tensile Strength at Break = 4930 psi Product List

Mechanical Properties

Tips: 30 items are displayed at most. For the rest of the results, please contact customer service.

Mechanical Properties	Metric	English	Comments
Tensile Strength at Break	34.0 MPa	4930 psi	50 mm/min; ISO 527
SABIC Innovative Plastics Cycolac® MG38 ABS (Europe-Africa-Middle East) Very high impact ABS. Toughness/rigidity. Good fatigue resistance.
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 5 mm/min; ASTM D638
SABIC Innovative Plastics Cycolac® MG38N ABS (Asia Pacific) Very high impact ABS. Toughness/rigidity. Good fatigue resistance. NSF Standard 61 certified in limited colors (restrictions may apply)>
Tensile Strength at Break	34.0 MPa	4930 psi	50 mm/min; ISO 527
SABIC Innovative Plastics Geloy XTWM200 ASA (Asia Pacific) ASA resin for injection molding. Excellent flow, colorability and outdoor weathering capability.This data was supplied by SABIC-IP for the Asia Pacific region.
Tensile Strength at Break	34.0 MPa	4930 psi
Plastcom SLOVALEN PH 92 T 30 PP, 30% mineral filling FeaturesModified PP for injection moulding with the content of 30% mineral filling. Increased rigidity, strength and thermal. Decreased shrinkage. General application in all industry branches.Packag..
Tensile Strength at Break	<= 34.0 MPa	<= 4930 psi	ISO/R527
Polykemi AB POLYfill PPH T15020 Polypropylene Homopolymer, Mineral Reinforced Information provided by Polykemi AB
Tensile Strength at Break	34.0 MPa @Temperature 23.0 °C	4930 psi @Temperature 73.4 °F	50 mm/min; ASTM D638
Solvay Specialty Polymers Halar® 1450LC Polyethylene, Chlorotrifluoroethylene (ECTFE) (Unverified Data**) Information provided by Solvay Specialty Polymers.
Tensile Strength at Break	34.0 MPa	4930 psi	Sintered Sheet; ISO 12086
3M Dyneon™ TFM™ 2001 PTFE (discontinued **) Processable by standard paste extrusion methodRecommended for high performance applications with reduction ratios up to 1000:1Provides denser polymer structure with fewer micro voids and lower gas p..
Tensile Strength at Break	34.0 MPa	4930 psi	ISO 37
Huntsman AVALONÂ® 98 AE Thermoplastic Polyurethane Introduction: AVALON 98 AE is a general purpose polyester based thermoplastic polyurethane for injection molding. AVALON 98 AE is part of the AVALON Perform Range and offers a premium soiling materi..
Tensile Strength at Break	34.0 MPa	4930 psi	ISO 527
FKuR Kunststoff FibrolonÂ® F 8530 Biodegradable Wood-Plastic Compound, Fiber Reinforced FIBROLONÂ® are fiber reinforced compounds. Depending on specific customer requirements either a biodegradable polymer or a polyolefin can be used as the polymeric matrix. With the brand name of F..
Tensile Strength at Break	34.0 MPa	4930 psi	ISO 37
Huntsman AVALONÂ® 92 AB Thermoplastic Polyurethane Introduction: AVALON 92 AB is a high performance polyester based thermoplastic polyurethane for injection molding. AVALON 92 AB is part of the AVALON Performance Range and offers a premium soling ma..
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 5 mm/min; ASTM D638
SABIC Innovative Plastics LNP THERMOCOMP AX08306 ABS LNP* THERMOCOMP* AX08306 is a compound based on ABS resin containing Proprietary Filler(s). Added feature of this grade is: Platable.
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 5 mm/min; ASTM D638
SABIC Innovative Plastics LNP THERMOCOMP HX03408 PA11 LNP* Thermocomp* HX03408 is a compound based on Nylon 11 containing Proprietary Fillers. Added feature includes: Clean Compound System
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 5 mm/min; ASTM D638
SABIC Innovative Plastics LNP THERMOCOMP MX06402H PP LNP* THERMOCOMP* MX06402H is a compound based on Polypropylene resin containing 20% Glass Fiber. Added features of this material include: Heat Stabilized, Low Extractable.
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 5 mm/min; ASTM D638
SABIC Innovative Plastics LNP THERMOCOMP MF002AS PP LNP THERMOCOMP* MF002AS is a compound based on Polypropylene resin containing 10% Glass Fiber. Added features of this material include: Heat Stabilized.
Tensile Strength at Break	34.0 MPa	4930 psi	Crosshead speed 100 mm/min; ISO 527
SCG Chemicals EL-Leneâ„¢ H5211P High Density Polyethylene Pipe Resin Key Characteristics: Good processing, high thermal stabilityRecommended Applications: Water pipes, conduit, sewage drainage pipesInformation provided by SCG Chemicals
Tensile Strength at Break	34.0 MPa	4930 psi	ISO 527
Total HP 401 MDPE, pipe, cable, sheet FINATHENE® HP 401 is a polyethylene copolymer based on C6 hexene as co-monomer and is produced by a continuous low-pressure slurry polymerization process. FINATHENE® HP 401 is a black high densit..
Tensile Strength at Break	34.0 MPa	4930 psi	ISO 527-1/-2
DuPont Performance Polymers Hytrel® 4556 Polyester Elastomer TPC-ET (Unverified Data**) 45 Shore D High Performance Polyester ElastomerInformation provided by DuPont Performance Polymers
Tensile Strength at Break	34.0 MPa	4930 psi	ISO R 527
Fainplast Compounds RE 116 Rigid PVC, Extrusion Small tubes for shoes
Tensile Strength at Break	34.0 MPa	4930 psi	50 mm/min; ISO 527
Chi Mei Polylac® PA-756H ABS - High Flow Super high flow
Tensile Strength at Break	34.0 MPa	4930 psi	50 mm/min; ISO 527
Chi Mei Polylac® PA-777B ABS - High Heat High Heat Impact
Tensile Strength at Break	34.0 MPa	4930 psi	ASTM D638
Azdel SuperLite® SL551800-100 PP Resin Matrix / 55% Glass Fiber (4 mm Molded Thickness) AZDEL SuperLite® SL551800-100 is a low pressure, thermoformable, thermoplastic composite of polypropylene and long chopped glass fibers. Usually combined with outer layers as needed for the applic..
Tensile Strength at Break	34.0 MPa	4930 psi
AorTech Biomaterials ECSil™ 90A Biomedical Carbonate Silicone Pellets Elast-Eon™ Carbonate Silicone (ECSil™) is a family of next generation biomedical polymers. ECSil™ is finding strong interest in cardiac pacing leads, orthopaedics, spinal discs, and generally an..
Tensile Strength at Break	34.0 MPa	4930 psi	ASTM D638
3M Dyneon™ PFA FLEX 8515 UHPZ Perfluoroalkoxy Fluorothermoplastic Granules Dyneon™ PFA-FLEX UHP family exhibits improved environmental stress crack resistance to stress cracking agents such as fluorsurfactants and fluorosurfactant-containing chemicals. In addition, this f..
Tensile Strength at Break	34.0 - 40.0 MPa	4930 - 5800 psi	ASTM D638
Arkema Group KYNAR FLEX® 3120-15 Polyvinylidene Fluoride Copolymer - Extrusion & Molding Characteristics: Natural resin - translucent, off-white hemispheres. Flexible, flame and smoke suppressant. High stability in harsh thermal, chemical and ultraviolet environments. High toughness..
Tensile Strength at Break	34.0 - 55.0 MPa	4930 - 7980 psi	ASTM D638
Arkema Group KYNAR® 740 Black/Red Polyvinylidene Fluoride Homopolymer - Injection Molding and Extrusion Characteristics: Pigmented. High stability in harsh thermal, chemical and ultraviolet environments. High toughness and mechanical strength, low permeability, abrasion resistance; high purityAppli..
Tensile Strength at Break	34.0 - 55.0 MPa	4930 - 7980 psi	ASTM D638
Arkema Group KYNAR® 740 Polyvinylidene Fluoride Homopolymer - Injection Molding and Extrusion Characteristics: Natural resin - translucent, off-white hemispheres. High stability in harsh thermal, chemical and ultraviolet environments. High toughness and mechanical strength, low permeabili..
Tensile Strength at Break	34.0 MPa	4930 psi
AorTech Biomaterials Elast-Eon™ E2-862 Biomedical Polyurethane Pellets Elast-Eon™ polymers are used in biomedical applications. They have high biostability so they can be used for long term implantation.
Tensile Strength at Break	34.0 MPa	4930 psi	DIN EN ISO 527-3
3M Dyneon™ TF 2025Z PTFE Fine Powder Dyneon™ TF 2025 Z PTFE is an ideal grade for pipe liner applications in chemical plant construction due to high green strength.Product Features:High molecular weightFine powder grade for low to med..
Tensile Strength at Break	34.0 MPa	4930 psi	Sintered Molding; DIN 53455 (film, 0.2mm)
3M Dyneon™ TFM™ 1630 PTFE (discontinued **) Semi-free-flowing resin for convenient handlingHigh bulk density leading to more economical processingVery dense polymer structure; low permeabilityGood electrical and mechanical propertiesSmoother ..
Tensile Strength at Break	34.0 MPa	4930 psi	Type I, 50 mm/min; ASTM D638
SABIC Innovative Plastics GELOY CR7520 ASA (Asia Pacific) ASA copolymer. Automotive grilles and exteriors. Excellent weatherability, good flow/aesthetics and high impact. Rated f2 by UL.