Quadrant EPP Ertalon® 4.6 PA 4.6, extruded (ISO Data)

Category	Polymer , Thermoplastic , Nylon , Nylon 46 , Nylon 46, Unreinforced
Manufacturer	Quadrant Engineering Plastics Products
Trade Name	Ertalon®
Port	Ningbo port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Quadrant EPP Ertalon® 4.6 PA 4.6, extruded (ISO Data).pdf
Price	EMAIL US sales@lookpolymers.com

Material Notes:

Compared with conventional nylons, Ertalon 4.6 features a better retention of stiffness and creep resistance over a wide range of temperatures as well as superior heat ageing resistance. Therefore, applications for Ertalon 4.6 are situated in the “higher temperature area” (80 – 150 °C) where stiffness, creep resistance, heat ageing resistance, fatigue strength and wear resistance of PA 6, PA 66, POM and PET fall short. High mechanical strength, stiffness, hardness and toughness Good fatigue resistance High mechanical damping ability Good sliding properties Excellent wear resistance Good electrical insulating properties Good resistance to high energy radiation (gamma- and X-rays) Good machinability

Physical Properties	Metric	English	Comments
Density	1.19 g/cc	0.0430 lb/in³	ISO 1183-1
Moisture Absorption at Equilibrium	2.8 %	2.8 %	50% RH
Water Absorption at Saturation	9.5 %	9.5 %

Mechanical Properties	Metric	English	Comments
Hardness, Rockwell M	92	92	ISO 2039-2
Hardness, Shore D	80	80
Ball Indentation Hardness	165 MPa	23900 psi	ISO 2039-1
Tensile Strength	105 MPa	15200 psi	at Yield; ISO 527-1/-2
Elongation at Break	25 %	25 %	ISO 527-1/-2
Elongation at Yield	18 %	18 %	ISO 527-1/-2
Tensile Modulus	3.40 GPa	493 ksi	ISO 527-1/-2
Flexural Strength	138 MPa	20000 psi
Flexural Modulus	3.23 GPa	468 ksi
Compressive Strength	31.0 MPa @Strain 1 %	4500 psi @Strain 1 %	ISO 604
	60.0 MPa @Strain 2 %	8700 psi @Strain 2 %	ISO 604
	102 MPa @Strain 5 %	14800 psi @Strain 5 %	ISO 604
K Factor (ISO)	18 µm/km	18 µm/km
Charpy Impact Unnotched	NB	NB	ISO 179-1/1eU
Charpy Impact, Notched	0.800 J/cm²	3.81 ft-lb/in²	ISO 179-1/1eA
Coefficient of Friction, Dynamic	0.40 - 0.60	0.40 - 0.60
Limiting Pressure Velocity	0.100 MPa-m/sec	2860 psi-ft/min	at 1 m/s unlubricated
	0.160 MPa-m/sec	4570 psi-ft/min	at 0.1 m/s unlubricated

Thermal Properties	Metric	English	Comments
CTE, linear	90.0 µm/m-°C @Temperature 23.0 - 100 °C	50.0 µin/in-°F @Temperature 73.4 - 212 °F
Thermal Conductivity	0.300 W/m-K	2.08 BTU-in/hr-ft²-°F
Melting Point	290 °C	554 °F	DSC, 10°C/min.; ISO 11357-1/-3
Maximum Service Temperature, Air	130 °C	266 °F	Continuous; 20,000 h
	150 °C	302 °F	Continuous; 5,000 h
Deflection Temperature at 1.8 MPa (264 psi)	160 °C	320 °F	ISO 75-1/-2
Flammability, UL94	HB	HB
Oxygen Index	24 %	24 %	ISO 4589-1/-2

Electrical Properties	Metric	English	Comments
Volume Resistivity	>= 1.0e+14 ohm-cm	>= 1.0e+14 ohm-cm	IEC 60093
Surface Resistivity per Square	>= 1.0e+13 ohm	>= 1.0e+13 ohm	IEC 60093
Dielectric Constant	3.8 @Frequency >=100000 Hz	3.8 @Frequency >=100000 Hz	IEC 60250
Dielectric Strength	25.0 kV/mm	635 kV/in
Dissipation Factor	0.0090 @Frequency 100000 Hz	0.0090 @Frequency 100000 Hz	IEC 60250
Comparative Tracking Index	400 V	400 V	IEC 60112

Compliance Properties	Metric	English
3A-Dairy	No	No
European Food 1935/2004	No	No
FDA	No	No
USP Class VI	No	No

Chemical Resistance Properties	Metric	English
Acids, Strong (pH 1-3)	Unacceptable	Unacceptable
Acids, Weak	Limited	Limited
Alcohols	Limited	Limited
Alkalies, Strong (pH 11-14)	Unacceptable	Unacceptable
Alkalies, Weak	Limited	Limited
Chlorinated Solvents	Limited	Limited
Continuous Sunlight	Limited	Limited
Hot Water / Steam	Limited	Limited
Hydrocarbons - Aliphatic	Acceptable	Acceptable
Hydrocarbons - Aromatic	Acceptable	Acceptable
Inorganic Salt Solutions	Acceptable	Acceptable
Ketones, Esters	Acceptable	Acceptable

Users viewing this material also viewed the following: