Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 2.05 g/cc | 0.0741 lb/in³ | Green Density |
Nabaltec NABALOX® NO 313 Ground Alumina NABALOX® aluminum oxide has a number of advantages including low sintering temperaturewide sintering rangeflexible processinghigh sintered densities high wear and impact resistanceelectrical insula.. |
|||
Density | 2.05 - 2.15 g/cc | 0.0741 - 0.0777 lb/in³ | ASTM D792 |
Polikim EFALON® K-25 PTFE, 25% Carbon Filled K25 and K35 have less thermal expansion, higher wear resistance, less deformation under load properties compared to virgin Efalon® (PTFE). Applications: Bearings, piston rings, gaskets, seal rings... |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | |
Cookson Group Plaskon® 435 Mineral Filled Epoxy Molding Compound
(discontinued **) Test specimens were transfer molded and post cured 4 hours at 175°C.Combines exceptional reliability with wide molding process latitude. This material is designed to encapsulate a variety of semic.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | ASTM D792 |
Chevron Phillips Ryton® R10-110BL Polyphenylene Sulfide Compound
(discontinued **) Black Polyphenylene Sulfide CompoundRyton® R10-110BL is a glass and mineral filled polyphenylene sulfide compound which provides a good combination of mechanical and electrical properties.Applicati.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | estimated by MatWeb |
Garlock GYLON® 3540 Microcellular PTFE Gasketing Microcellular PTFE.Highly compressible PTFE seals under low bolt load- suitable for many non-metallic flangesCompressible material conforms to surface irregularities, especially on warped, pitted or.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | estimated by MatWeb |
Garlock GYLON® 3545 Layered Microcellular PTFE Gasketing Microcellular PTFE gasket with rigid PTFE coreHighly compressible PTFE outer layers seal under low bolt load- suitable for many non-metallic flangesCompressible layers conform to surface irregularit.. |
|||
Density | 2.05 - 2.11 g/cc | 0.0741 - 0.0762 lb/in³ | molded; ASTM D792 |
Guarniflon PTFE G453 Polytetrafluoroethylene 25% Carbographite PTFE G Standard Compound with carbon..Properties: Good thermal and electrical conductivity. Good resistance to deformation. Excellent resistance to load with low coefficient of friction and high .. |
|||
Density | 2.05 - 2.11 g/cc | 0.0741 - 0.0762 lb/in³ | molded; ASTM D792 |
Guarniflon PTFE G456 Polytetrafluoroethylene 25% Hard Carbon PTFE G Special Compound with carbon..Properties: Good thermal and electrical conductivity. Good resistance to deformation. Excellent resistance to load with low coefficient of friction and high w.. |
|||
Density | 2.05 g/cc @Temperature 77.9 °C |
0.0741 lb/in³ @Temperature 172 °F |
Liquid at mp |
Indium Corp. GaCl3 Gallium Trichloride, Anhydrous Synonyms: Gallium Chloride, Gallium (III) ChlorideCAS Number: 13450-90-3EC Number: 236-610-0RTECS: LW9100000Purity: 99.5 to 99.999% Gallium TrichlorideAppearance: Clear or White, Needle-shaped.. |
|||
Density | 2.05 - 2.11 g/cc | 0.0741 - 0.0762 lb/in³ | molded; ASTM D792 |
Guarniflon PTFE G415 Polytetrafluoroethylene 25% Soft Carbon PTFE G Standard Compound with carbon..Properties: Good thermal and electrical conductivity. Good resistance to deformation. Excellent resistance to load with low coefficient of friction and high .. |
|||
Density | 2.05 - 2.13 g/cc | 0.0741 - 0.0770 lb/in³ | BS2782:Pt6 |
Dalau Dalcon 021 75% Virgin PTFE, 25% Carbon Coke Applications & Industries: General: Carbon / Coke (soft) filler is good in dry running conditions, adds to the creep resistance, increases the hardness and raises the thermal conductivity of PTFE; C.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | |
Trelleborg Emerson & Cuming Stycast® 5952 Two-Component Easy Mix Ratio Encapsulant Features and Typical ApplicationsPrimarily designed for ease of use in either meter mix or manual dispense operations. These products also offer a wide range of features including heat dissipation, .. |
|||
Density | 2.05 - 2.13 g/cc | 0.0741 - 0.0770 lb/in³ | BS2782:Pt6 |
Dalau Dalcon 021 75% Virgin PTFE, 25% Carbon Coke Applications & Industries: General: Carbon / Coke (soft) filler is good in dry running conditions, adds to the creep resistance, increases the hardness and raises the thermal conductivity of PTFE; C.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | |
BNZ Materials Blazecrete 2800 Dense Castable Blazecrete 2800 is an economical, high alumina refractory for service to 2800°F (1556°C). Suitable for door linings, curbs and covers, pre-cast shapes, grey iron ladles, aluminum reverberatory fur.. |
|||
Density | 2.05 - 2.15 g/cc | 0.0741 - 0.0777 lb/in³ | |
Aremco Ceramabond™ 671 High Temperature Ceramic Adhesive/Paste, Alumina Filled Aremco's ceramic adhesives are easy to use, one- and two-component systems which air dry in 1-2 hrs and are ready for use following a 200 to 700 °F cure. These materials are mostly water-based and.. |
|||
Density | 2.05 g/cc | 0.0741 lb/in³ | |
LATI Latimass 52/11-01 D020 PP Homopolymer Specific density compound based on Polypropylene homopolymer (PPh). Special filler. Availability: Africa & Middle East; Asia Pacific; Europe; Latin America; North AmericaInformation provided by Lati.. |