Category | Polymer , Thermoplastic , Polyphenylene Sulfide (PPS) , Polyphenylene Sulfide (PPS) with 40% Glass Fiber Filler |
Manufacturer | |
Trade Name | |
Port | Ningbo port,China |
Trade Terms | FOB, CFR, CIF |
Payment Terms | L/C, T/T, Western Union |
Download PDF | Solvay Specialty Polymers Ryton® R-4 Polyphenylene Sulfide Compound
(Unverified Data**).pdf ![]() |
Price | EMAIL US sales@lookpolymers.com |
Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 1.65 g/cc | 0.0596 lb/in³ | ASTM D792 |
Water Absorption | 0.050 % | 0.050 % | ASTM D570 |
Linear Mold Shrinkage | 0.0030 cm/cm | 0.0030 in/in | 102 mm X 102 mm X 3.2 mm Plaques, Edge Gated |
Linear Mold Shrinkage, Transverse | 0.0050 cm/cm | 0.0050 in/in | Measured on 102 mm X 102 mm X 3.2 mm Plaques, Edge Gated |
Deformation | 0.79 % | 0.79 % | at 266°F for 0.5 inch cube under 2 ksi load. |
Mechanical Properties | Metric | English | Comments |
---|---|---|---|
Hardness, Rockwell R | 123 | 123 | ASTM D785 |
Hardness, Shore D | 89 | 89 | |
Tensile Strength, Ultimate | 160 MPa | 23200 psi | ASTM D638 |
Elongation at Break | 1.1 % | 1.1 % | ASTM D638 |
Modulus of Elasticity | 15.2 GPa | 2200 ksi | |
15.2 GPa | 2200 ksi | Loading Rate 0.1 inch/min | |
Flexural Yield Strength | 195 MPa | 28300 psi | ASTM D790 |
Flexural Modulus | 15.0 GPa | 2180 ksi | ASTM D790 |
Compressive Yield Strength | 240 MPa | 34800 psi | ASTM D695 |
Poissons Ratio | 0.38 | 0.38 | |
Fatigue Strength | 56.0 MPa @# of Cycles 1.00e+6 |
8120 psi @# of Cycles 1.00e+6 |
10 Hz, ASTM Type I tensile bar |
Shear Modulus | 5.51 GPa | 799 ksi | Calculated |
Shear Strength | 103 MPa | 15000 psi | |
Izod Impact, Notched | 0.850 J/cm | 1.59 ft-lb/in | ASTM D256 |
0.801 J/cm @Temperature -40.0 °C |
1.50 ft-lb/in @Temperature -40.0 °F |
||
Izod Impact, Unnotched | 3.20 J/cm | 5.99 ft-lb/in | ASTM D256 |
2.03 J/cm @Temperature -40.0 °C |
3.80 ft-lb/in @Temperature -40.0 °F |
||
Coefficient of Friction, Dynamic | 0.55 | 0.55 | vs. steel; 100 rpm, 29 fpm |
Coefficient of Friction, Static | 0.50 | 0.50 | vs. steel |
Taber Abrasion, mg/1000 Cycles | 70 | 70 | CS-10 wheel; 1 kg |
Thermal Properties | Metric | English | Comments |
---|---|---|---|
CTE, linear | 21.0 µm/m-°C @Temperature 100 - 200 °C |
11.7 µin/in-°F @Temperature 212 - 392 °F |
Axial; ASTM E831 |
21.0 µm/m-°C @Temperature -50.0 - 50.0 °C |
11.7 µin/in-°F @Temperature -58.0 - 122 °F |
Axial; ASTM E831 | |
CTE, linear, Transverse to Flow | 45.0 µm/m-°C @Temperature 20.0 °C |
25.0 µin/in-°F @Temperature 68.0 °F |
ASTM E831 |
84.0 µm/m-°C @Temperature 100 - 200 °C |
46.7 µin/in-°F @Temperature 212 - 392 °F |
ASTM E831 | |
Specific Heat Capacity | 1.03 J/g-°C | 0.247 BTU/lb-°F | |
Thermal Conductivity | 0.320 W/m-K | 2.22 BTU-in/hr-ft²-°F | |
Maximum Service Temperature, Air | 200 °C | 392 °F | UL Temperature Index 200 / 220 per UL746B |
Deflection Temperature at 1.8 MPa (264 psi) | >= 260 °C | >= 500 °F | Annealed 2 hr @ 200°C; ASTM D658 |
Flammability, UL94 | 5VA | 5VA | UL94 V-0/5VA |
Oxygen Index | 47 % | 47 % |
Electrical Properties | Metric | English | Comments |
---|---|---|---|
Electrical Resistivity | 1.00e+16 ohm-cm | 1.00e+16 ohm-cm | ASTM D257 |
Surface Resistance | 1.00e+11 ohm @Temperature 90.0 °C |
1.00e+11 ohm @Temperature 194 °F |
95% RH, 48 hrs |
Insulation Resistance | 1.00e+11 ohm | 1.00e+11 ohm | Accelerated; 194°F; 95% RH; 2 days; ASTM D257 |
Dielectric Constant | 3.8 @Frequency 1e+6 Hz |
3.8 @Frequency 1e+6 Hz |
ASTM D150 |
3.9 @Frequency 1000 Hz |
3.9 @Frequency 1000 Hz |
ASTM D150 | |
Dielectric Strength | 18.0 kV/mm | 457 kV/in | ASTM D149 |
Dissipation Factor | 0.0020 @Frequency 1000 Hz |
0.0020 @Frequency 1000 Hz |
ASTM D150 |
0.0020 @Frequency 1e+6 Hz |
0.0020 @Frequency 1e+6 Hz |
ASTM D150 | |
Arc Resistance | 125 sec | 125 sec | ASTM D495 |
Comparative Tracking Index | 130 V | 130 V | UL 746A |