Mechanical Properties | Metric | English | Comments |
---|---|---|---|
Tensile Strength, Yield | 240 MPa @Strain 1.00 % |
34800 psi @Strain 1.00 % |
EN min.,RT; EN 10002-1 |
Outokumpu 4307 Cr-Ni Austenitic Stainless Steel General purpose steel with good corrosion resistance.Applications: Wide variety of applications in construction, chemical, petroleum, automobile, and domestic appliance markets.Available in hot roll.. |
|||
Tensile Strength, Yield | 240 MPa @Strain 1.00 %, Temperature 100 °C |
34800 psi @Strain 1.00 %, Temperature 212 °F |
EN min.; EN 10002-5 |
Outokumpu 4311 Cr-Ni Austenitic Stainless Steel Applications: Wet corrosion resistance and general service.Available in hot rolled plate (Quarto), hot rolled strip/sheet (CPP), cold rolled strip/sheet, cold rolled narrow strip, bar, and rod forms.. |
|||
Tensile Strength, Yield | 240 MPa @Strain 1.00 % |
34800 psi @Strain 1.00 % |
EN min.,RT; EN 10002-1 |
Outokumpu 4541 Cr-Ni Austenitic Stainless Steel Good corrosion resistance and weldable. Resistant to sensitization.Applications: Welded screensFurnace beltsCatalytic converter meshAvailable in hot rolled plate (Quarto), hot rolled strip/sheet (C.. |
|||
Tensile Strength, Yield | 240 MPa @Strain 1.00 %, Temperature 400 °C |
34800 psi @Strain 1.00 %, Temperature 752 °F |
EN min.; EN 10002-5 |
Outokumpu 4565 High Performance Austenitic Stainless Steel Applications: Process equipment in chemical industryBleaching equipment in the pulp and paper industryFlue-gas cleaningDesalinationSeawater handlingHeat exchangersAvailable in hot rolled plate (Quar.. |
|||
Tensile Strength, Yield | >= 240 MPa @Temperature 20.0 °C |
>= 34800 psi @Temperature 68.0 °F |
|
PEAK Werkstoff DISPAL S270 Aluminum Alloy, AlSi25Fe4Ni3CuMgMnCrTi, Condition F Excellent properties:abrasive stabilityhigh stiffness (E-modulus)resistance even at high temperaturesgood grindabilityPEAK DISPAL materials allow the manufacturing of pistons for highest operational.. |
|||
Tensile Strength, Yield | 240 MPa @Strain 0.200 % |
34800 psi @Strain 0.200 % |
Typical after Solution Annealing |
Industeel SIRIUS 309 23% Cr - 13% Ni Heat Resistant Stainless Steel Description: CLI SIRIUS 309 grade is a fully austenitic stainless steel containing 23% Cr, and 13% Ni additions. The alloy is well known for its multi-purpose high temperature corrosion resistance b.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 254 - 305 mm |
>= 34800 psi @Strain 0.200 %, Thickness 10.0 - 12.0 in |
Tempers T851/T852 |
Constellium Alumold® 350 Aluminum Alumold-350® has been specifically developed to achieve the best combination of strength at low and high temperatures, together with a good shape stability and machinability. Alumold-350® is parti.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 3.90 - 6.00 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.154 - 0.236 in |
Temper T651; Standard EN 485-2 |
Constellium PLAN 6061 Aluminum Rolled Plate Rolled plates in 6061 PLAN are optimized for minimum residual stress and improved dimensional tolerances. 6061 PLAN is mainly used for medium stressed mechanical components, manufactured by intensiv.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 6.00 - 12.5 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.236 - 0.492 in |
Temper T651; Standard EN 485-2 |
Constellium PLAN 6061 Aluminum Rolled Plate Rolled plates in 6061 PLAN are optimized for minimum residual stress and improved dimensional tolerances. 6061 PLAN is mainly used for medium stressed mechanical components, manufactured by intensiv.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 12.5 - 40.0 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.492 - 1.57 in |
Temper T651; Standard EN 485-2 |
Constellium PLAN 6061 Aluminum Rolled Plate Rolled plates in 6061 PLAN are optimized for minimum residual stress and improved dimensional tolerances. 6061 PLAN is mainly used for medium stressed mechanical components, manufactured by intensiv.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 80.0 - 100 mm |
>= 34800 psi @Strain 0.200 %, Thickness 3.15 - 3.94 in |
Temper T651; Standard EN 485-2 |
Constellium PLAN 6061 Aluminum Rolled Plate Rolled plates in 6061 PLAN are optimized for minimum residual stress and improved dimensional tolerances. 6061 PLAN is mainly used for medium stressed mechanical components, manufactured by intensiv.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 12.5 - 60.0 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.492 - 2.36 in |
Temper T651; Standard EN 485-2 |
Constellium Planoxal® 60 Aluminum plate The advantage of Planoxal®-60 plates over other standard EN AW-6082 alloy products is their low level of internal stress. They are also suitable for technical anodizing. Planoxal®-60 is mainly use.. |
|||
Tensile Strength, Yield | 240 MPa @Temperature 816 °C |
34800 psi @Temperature 1500 °F |
|
Crucible Steel XM-19 Stainless Steel Crucible XM-19 Stainless is a nitrogen strengthened, low carbon, austenitic, stainless steel that provides good corrosion resistance in combination with high strength. The alloy has better corrosio.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 12.5 - 40.0 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.492 - 1.57 in |
Temper T651; Standard EN 485-2 |
Constellium ALPLAN® 6061 Rolled Precision Aluminum Plate, Milled Both Sides Precision plates in ALPLAN® 6061 are milled on both sides and have a very low level of residual stress, thus avoiding excessive deformation during machining. Thanks to its very good dimensional sta.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 40.0 - 80.0 mm |
>= 34800 psi @Strain 0.200 %, Thickness 1.57 - 3.15 in |
Temper T651; Standard EN 485-2 |
Constellium ALPLAN® 6061 Rolled Precision Aluminum Plate, Milled Both Sides Precision plates in ALPLAN® 6061 are milled on both sides and have a very low level of residual stress, thus avoiding excessive deformation during machining. Thanks to its very good dimensional sta.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 12.5 - 60.0 mm |
>= 34800 psi @Strain 0.200 %, Thickness 0.492 - 2.36 in |
Temper T651; Standard EN 485-2 |
Constellium ALPLAN® 6082 Rolled Precision Aluminum Plate, Milled Both Sides Precision plates in ALPLAN® 6082 are milled on both sides and have a very low level of residual stress, thus avoiding excessive deformation during machining. Thanks to its very good dimensional sta.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 %, Thickness 100 - 140 mm |
>= 34800 psi @Strain 0.200 %, Thickness 3.94 - 5.51 in |
Temper T651; Standard EN 485-2 |
Constellium ALPLAN® 6082 Rolled Precision Aluminum Plate, Milled Both Sides Precision plates in ALPLAN® 6082 are milled on both sides and have a very low level of residual stress, thus avoiding excessive deformation during machining. Thanks to its very good dimensional sta.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 % |
>= 34800 psi @Strain 0.200 % |
Minimum |
Aleris Weldural Aluminum Alloy, 400 mm Thickness Sample treatment not specified for property data.Applications include precise mechanical parts with high dimensional stability, machine components, molds, and refrigeration engineering. Good weldab.. |
|||
Tensile Strength, Yield | >= 240 MPa @Strain 0.200 % |
>= 34800 psi @Strain 0.200 % |
Minimum |
Aleris Weldural Aluminum Alloy, 300 mm Thickness Sample treatment not specified for property data.Applications include precise mechanical parts with high dimensional stability, machine components, molds, and refrigeration engineering. Good weldab.. |