Category | Polymer , Thermoset , Polyurethane, TS , Thermoset Polyurethane Foam, Unreinforced |
Manufacturer | Rogers Corporation |
Trade Name | Poron® |
Port | Shanghai port,China |
Trade Terms | FOB, CFR, CIF |
Payment Terms | L/C, T/T, Western Union |
Download PDF | Rogers Corporation Poron® 4701-41-20 Urethane Foam, Soft, Enhanced Sealability.pdf |
Price | EMAIL US sales@lookpolymers.com |
Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 0.320 g/cc | 0.0116 lb/in³ | ASTM D3574-95 Test A |
Water Absorption | 13 % | 13 % | Immersion; ASTM D570-95 |
Moisture Absorption at Equilibrium | 2.0 % | 2.0 % | High Humidity; AMS 3568-95 |
Thickness | 1570 - 3180 microns | 62.0 - 125 mil | Range of Thicknesses Available |
Outgassing - Total Mass Loss | 0.040 % @Temperature 125 °C, Time 86400 sec |
0.040 % @Temperature 257 °F, Time 24.0 hour |
CVCM; at 7000 Pa; ASTM E595-93 |
0.46 % @Temperature 125 °C, Time 86400 sec |
0.46 % @Temperature 257 °F, Time 24.0 hour |
WVR; at 7000 Pa; ASTM E595-93 | |
0.97 % @Temperature 125 °C, Time 86400 sec |
0.97 % @Temperature 257 °F, Time 24.0 hour |
TML; at 7000 Pa; ASTM E595-93 |
Mechanical Properties | Metric | English | Comments |
---|---|---|---|
Hardness, Shore O | 24 | 24 | ASTM D2240-97 |
Tensile Strength | >= 0.517 MPa | >= 75.0 psi | ASTM D3574-75 Test E |
0.607 MPa | 88.0 psi | Typical; ASTM D3574-75 Test E | |
Elongation at Break | >= 100 % | >= 100 % | ASTM D3574-75 Test E |
140 % | 140 % | Typical; ASTM D3574-75 Test E | |
Compressive Yield Strength | 0.0689 - 0.117 MPa @Strain 25.0 % |
10.0 - 17.0 psi @Strain 25.0 % |
Range, 0.2"/min. strain rate |
0.103 MPa @Strain 25.0 % |
15.0 psi @Strain 25.0 % |
Typical value, 0.2"/min. strain rate | |
Tear Strength | >= 1.40 kN/m | >= 7.99 pli | ASTM D264-91 Die C |
2.30 kN/m | 13.1 pli | Typical; ASTM D264-91 Die C | |
Compression Set | 5.0 % @Temperature 23.0 °C |
5.0 % @Temperature 73.4 °F |
ASTM D1667-90 Test D |
5.0 % @Temperature 121 °C |
5.0 % @Temperature 250 °F |
autoclaved 5 hrs; ASTM D3574-95 J/Test D | |
10 % @Temperature 70.0 °C |
10 % @Temperature 158 °F |
ASTM D3574-95 Test D |
Thermal Properties | Metric | English | Comments |
---|---|---|---|
CTE, linear | 230 - 310 µm/m-°C | 128 - 172 µin/in-°F | |
Maximum Service Temperature, Air | 90.0 °C | 194 °F | Constant use; SAE J-2236 |
121 °C | 250 °F | Intermittent use; ASTM D746-98 |
Electrical Properties | Metric | English | Comments |
---|---|---|---|
Volume Resistivity | 1.00e+12 ohm-cm | 1.00e+12 ohm-cm | ASTM D257-99 |
Dielectric Constant | 1.71 @Time 86400 sec |
1.71 @Time 24.0 hour |
50% RH; ASTM D150 |
Dielectric Strength | 1.97 kV/mm | 50.0 kV/in | ASTM D149-97a |
Dissipation Factor | 0.050 | 0.050 | ASTM D150-98 |