Quadrant EPP TIVAR® Dryslide PE-UHMW + internal lubricant + other additives (ISO Data)

Category	Polymer , Thermoplastic , Polyethylene (PE) , HDPE , High Density Polyethylene (HDPE), UHMW PE Ultra High Molecular Weight
Manufacturer	Quadrant Engineering Plastics Products
Trade Name	TIVAR®
Port	Ningbo port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Quadrant EPP TIVAR® Dryslide PE-UHMW + internal lubricant + other additives (ISO Data).pdf
Price	EMAIL US sales@lookpolymers.com
	Online Service lookpolymers 27660005

Material Notes:

Thanks to the lubricant built into a PE-UHMW matrix with higher molecular weight, TIVAR DrySlide offers a lower coefficient of friction and enhanced wear and abrasion resistance than TIVAR 1000. The additives used also make this material static dissipative and considerably improve UV-resistance Electro Static Dissipative Ideal for dusty environments Helps reduce surging Won't mark packaging or products Corrosion-resistant Self-lubricating Reduces noise No moisture absorption

Physical Properties	Metric	English	Comments
Density	0.935 g/cc	0.0338 lb/in³	ISO 1183-1
Water Absorption	<= 0.10 %	<= 0.10 %	96 hr; ISO 62
Moisture Absorption at Equilibrium	<= 0.10 %	<= 0.10 %	50% RH
Water Absorption at Saturation	<= 0.10 %	<= 0.10 %	ISO 62
Outgassing - Total Mass Loss	0.14 %	0.14 %

Mechanical Properties	Metric	English	Comments
Hardness, Shore D	59	59
Ball Indentation Hardness	32.0 MPa	4640 psi	ISO 2039-1
Tensile Strength	18.0 MPa	2610 psi	at Yield; ISO 527-1/-2
Elongation at Break	>= 50 %	>= 50 %	ISO 527-1/-2
Elongation at Yield	20 %	20 %	ISO 527-1/-2
Tensile Modulus	0.650 GPa	94.3 ksi	ISO 527-1/-2
Flexural Strength	16.0 MPa	2320 psi
Compressive Strength	6.00 MPa @Strain 1 %	870 psi @Strain 1 %	ISO 604
	10.0 MPa @Strain 2 %	1450 psi @Strain 2 %	ISO 604
	16.0 MPa @Strain 5 %	2320 psi @Strain 5 %	ISO 604
K Factor (ISO)	6.0 µm/km	6.0 µm/km
Charpy Impact Unnotched	NB	NB	ISO 179-1/1eU
Charpy Impact, Notched	10.0 J/cm²	47.6 ft-lb/in²	Partial Break; ISO 179-1/1eA
Coefficient of Friction, Dynamic	0.15 - 0.30	0.15 - 0.30
Sand Slurry	85	85
Limiting Pressure Velocity	0.0500 MPa-m/sec	1430 psi-ft/min	at 1 m/s unlubricated
	0.0800 MPa-m/sec	2280 psi-ft/min	at 0.1 m/s unlubricated

Thermal Properties	Metric	English	Comments
CTE, linear	200 µm/m-°C @Temperature 23.0 - 100 °C	111 µin/in-°F @Temperature 73.4 - 212 °F
Thermal Conductivity	0.400 W/m-K	2.78 BTU-in/hr-ft²-°F
Melting Point	135 °C	275 °F	DSC, 10°C/min.; ISO 11357-1/-3
Maximum Service Temperature, Air	80.0 °C	176 °F	Continuous
Deflection Temperature at 1.8 MPa (264 psi)	42.0 °C	108 °F	ISO 75-1/-2
Flammability, UL94	HB	HB
Oxygen Index	<= 20 %	<= 20 %	ISO 4589-1/-2

Electrical Properties	Metric	English	Comments
Surface Resistivity per Square	<= 1.0e+8 ohm	<= 1.0e+8 ohm	IEC 60093

Compliance Properties	Metric	English
3A-Dairy	No	No
European Food 1935/2004	No	No
FDA	No	No
USP Class VI	No	No

Chemical Resistance Properties	Metric	English
Acids, Strong (pH 1-3)	Acceptable	Acceptable
Acids, Weak	Acceptable	Acceptable
Alcohols	Acceptable	Acceptable
Alkalies, Strong (pH 11-14)	Acceptable	Acceptable
Alkalies, Weak	Acceptable	Acceptable
Chlorinated Solvents	Acceptable	Acceptable
Conductive / Static Dissipative	Yes	Yes
Continuous Sunlight	Limited	Limited
Hot Water / Steam	Unacceptable	Unacceptable
Hydrocarbons - Aliphatic	Acceptable	Acceptable
Hydrocarbons - Aromatic	Limited	Limited
Inorganic Salt Solutions	Acceptable	Acceptable
Ketones, Esters	Acceptable	Acceptable

Users viewing this material also viewed the following: