- HOME
- POLYMER SEARCH
- Thermoplastic
- Fluoropolymer
- PTFE
- Polytetrafluoroethylene (PTFE), Mica Filled
- Quadrant EPP Fluorosint® 500 PTFE, synthetic mica-filled PTFE, compression molded (ASTM Product Data Sheet)
Quadrant EPP Fluorosint® 500 PTFE, synthetic mica-filled PTFE, compression molded (ASTM Product Data Sheet)
| Category | Polymer , Thermoplastic , Fluoropolymer , PTFE , Polytetrafluoroethylene (PTFE), Mica Filled |
| Manufacturer | Quadrant Engineering Plastics Products |
| Trade Name | Fluorosint® |
| Port | Ningbo port,China |
| Trade Terms | FOB, CFR, CIF |
| Payment Terms | L/C, T/T, Western Union |
| Download PDF | Quadrant EPP Fluorosint® 500 PTFE, synthetic mica-filled PTFE, compression molded (ASTM Product Data Sheet).pdf  |
| Price | EMAIL US sales@lookpolymers.com |
Material Notes:
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Specific Gravity | 2.32 g/cc | 2.32 g/cc | ASTM D792 |
| Water Absorption | 0.10 % | 0.10 % | Immersion, 24hr; ASTM D570(2) |
| Water Absorption at Saturation | 0.30 % | 0.30 % | Immersion; ASTM D570(2) |
| Deformation | 5.0 % | 5.0 % | 2000 psi; 122°F (50°C) |
| Mechanical Properties | Metric | English | Comments |
|---|---|---|---|
| Hardness, Rockwell R | 55 | 55 | ASTM D785 |
| Hardness, Shore D | 70 | 70 | ASTM D2240 |
| Tensile Strength | 7.58 MPa | 1100 psi | ASTM D638 |
| Elongation at Break | 30 % | 30 % | ASTM D638 |
| Tensile Modulus | 2.07 GPa | 300 ksi | ASTM D638 |
| Flexural Strength | 15.2 MPa | 2200 psi | ASTM D790 |
| Flexural Modulus | 3.45 GPa | 500 ksi | ASTM D790 |
| Compressive Strength | 27.6 MPa | 4000 psi | 10% Def.; ASTM D695 |
| Compressive Modulus | 1.72 GPa | 250 ksi | ASTM D695 |
| Shear Strength | 14.5 MPa | 2100 psi | ASTM D732 |
| Izod Impact, Notched | 0.481 J/cm | 0.900 ft-lb/in | ASTM D256 Type A |
| Coefficient of Friction, Dynamic | 0.15 | 0.15 | Dry vs. Steel; QTM55007 |
| K (wear) Factor | 1210 x 10-8 mm³/N-M | 600 x 10-10 in³-min/ft-lb-hr | QTM 55010 |
| Limiting Pressure Velocity | 0.280 MPa-m/sec | 8000 psi-ft/min | 4:1 safety factor; QTM 55007 |
| Thermal Properties | Metric | English | Comments |
|---|---|---|---|
| CTE, linear | 45.0 µm/m-°C @Temperature -40.0 - 149 °C |
25.0 µin/in-°F @Temperature -40.0 - 300 °F |
ASTM E831 |
| Thermal Conductivity | 0.764 W/m-K | 5.30 BTU-in/hr-ft²-°F | ASTM F433 |
| Melting Point | 327 °C | 621 °F | Crystalline, Peak; ASTM D3418 |
| Maximum Service Temperature, Air | 260 °C | 500 °F | Long Term |
| Deflection Temperature at 1.8 MPa (264 psi) | 132 °C | 270 °F | ASTM D648 |
| Flammability, UL94 | V-0 | V-0 | 1/8 inch (Estimated Rating) |
| Electrical Properties | Metric | English | Comments |
|---|---|---|---|
| Surface Resistivity per Square | >= 1.00e+13 ohm | >= 1.00e+13 ohm | EOS/ESD S11.11 |
| Dielectric Constant | 2.85 @Frequency 1e+6 Hz |
2.85 @Frequency 1e+6 Hz |
ASTM D150 |
| Dielectric Strength | 10.8 kV/mm | 275 kV/in | Short Term; ASTM D149 |
| Dissipation Factor | 0.0080 @Frequency 1e+6 Hz |
0.0080 @Frequency 1e+6 Hz |
ASTM D150 |
| Compliance Properties | Metric | English | Comments |
|---|---|---|---|
| 3A-Dairy | No | No | |
| Canada AG | No | No | |
| FDA | No | No | |
| NSF | No | No | |
| USDA | No | No | |
| USP Class VI | No | No |
| Chemical Resistance Properties | Metric | English | Comments |
|---|---|---|---|
| Acids, Strong (pH 1-3) | Acceptable | Acceptable | |
| Acids, Weak | Acceptable | Acceptable | |
| Alcohols | Acceptable | Acceptable | |
| Alkalies, Strong (pH 11-14) | Unacceptable | Unacceptable | |
| Alkalies, Weak | Acceptable | Acceptable | |
| Chlorinated Solvents | Acceptable | Acceptable | |
| Conductive / Static Dissipative | No | No | |
| Continuous Sunlight | Acceptable | Acceptable | |
| Hot Water / Steam | Limited | Limited | |
| Hydrocarbons - Aliphatic | Acceptable | Acceptable | |
| Hydrocarbons - Aromatic | Acceptable | Acceptable | |
| Inorganic Salt Solutions | Acceptable | Acceptable | |
| Ketones, Esters | Acceptable | Acceptable |
| Descriptive Properties | Value | Comments |
|---|---|---|
| Color | Natural | |
| Machinability | 2 | 1-10, 1=Easier to Machine |
Users viewing this material also viewed the following:
- Honeywell Aegis™ H135XP Nylon 6 Extrusion Grade Homopolymer Film (discontinued **)
- Lehmann & Voss LUVOCOM® 1-7791 Polyamide 66, with carbon fiber, PTFE, lubricant modified, heat stabilized
- Monmouth Rubber & Plastics Durafoamâ„¢ DK1111 NEO/EPDM Polymeric Blend
- Sylvin Technologies 9980-60 Natural PVC Molding Compound
- A. Schulman POLYBLAK™ 3225 Superior Black Color Concentrate, 50% Carbon Black Based In PP Homopolymer
- A. Schulman SCHULAMID® 66 MF40 Mineral Filled Nylon 66
- Chengdu Polyster 70 LPI Lenticular Lens Sheet, PP
- Eurostar Staramide AS3 PA66, 15% Glass Bead Reinforced, Injection Molding
- Azoty Tarnow™ Alphalon™ 27 Nylon 6
Copyright © lookpolymers.com All Rights Reserved