Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 7.86 g/cc | 0.284 lb/in³ | |
Indium Corp. Indalloy 70 Indium-Tin Solder Alloy Information Provided by Indium Corporation |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Lucas-Milhaupt SIL-FOS 6 Silver/ Copper/ Phosphorus Alloy Applications: Sil-Fos 6 is a low cost brazing filler metal suitable for joining copper to copper and copper to copper alloys where critical impact or vibration stresses are not encountered in servi.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Special Metals BRIGHTRAY® Alloy F Electrical Resistance Alloy A nickel-iron-chromium electrical-resistance alloy for use at temperatures up to 1920°F (1050°C) under continuous operating conditions. Its high iron content and relatively low level of nicke.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Special Metals INCOLOY® Alloy DS A nickel-iron-chromium alloy with an addition of silicon. It has good high-temperature strength and excellent resistance to oxidation and carburization. The silicon content makes the alloy resista.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Schmolz + Bickenbach P-20 High Hard Plastic Mold Steel Description: P-20 High Hard is an improved pre-hardened mold steel that has been specially designed for large plastic molds; Material is forged on a 5000 ton press assuring maximum deformation durin.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Schmolz + Bickenbach P-20 Modified Plastic Mold Steel Description: P-20 Modified is an improved pre-hardened mold steel that has been specially designed for large plastic molds; The material is forged on a 5000 ton press assuring maximum deformation du.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Wingate Alloys Winco NT 24 Nitrogen-Strengthened Austenitic Stainless Steel Winco NT 24 provides good aqueous corrosion resistance combined with resistance to abrasives, metal-to-metal wear and sustained heats of 1500°F. Higher mechanical properties than standard austeniti.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | H1150 |
Crucible Steel 17Cr-4Ni Precipitation Hardening Stainless Steel Crucible 17Cr-4Ni is a precipitation-hardening stainless steel which is capable of a high strength and hardness levels after a relatively simple heat-treatment procedure. This grade is martensitic a.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | H1150 |
Crucible Steel 17Cr-4Ni Super-X® Precipitation Hardening Stainless Steel Crucible 17Cr-4Ni is a version of 17CR-4Ni which has been modified to substantially improve machinability and other properties. Patented 17Cr-4Ni Super-X meets industry specifications for 17Cr-4Ni. .. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Crucible Steel AIRKOOL® (AISI A2) Tool Steel Airkool (AISI A2) is an air-hardening medium alloy tool steel which is heat treatable to HRC 60-62. It has wear resistance intermediate between the oil hardening tool steels (O1) and the high carbon.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Crucible Steel AISI 6150 Alloy Steel Information provided by Crucible Industries |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | As Annealed |
Eagle Brass 1008 Low Carbon Steel, 1/4 Hardened 1008 is a standard grade Carbon Steel. This alloy is generally used for "commercial quality" cold rolled steel. It is an economical, general purpose steel grade offering moderate strength and toughn.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | As Annealed |
Eagle Brass 1008 Low Carbon Steel, 1/2 Hardened 1008 is a standard grade Carbon Steel. This alloy is generally used for "commercial quality" cold rolled steel. It is an economical, general purpose steel grade offering moderate strength and toughn.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | As Annealed |
Eagle Brass 1008 Low Carbon Steel, Annealed 1008 is a standard grade Carbon Steel. This alloy is generally used for "commercial quality" cold rolled steel. It is an economical, general purpose steel grade offering moderate strength and toughn.. |
|||
Density | 7.86 g/cc @Temperature 600.0 °C |
0.284 lb/in³ @Temperature 1112 °F |
soft annealed |
Bohler-Uddeholm UDDEHOLM VANADIS 30 AISI M2 + Co SUPERCLEAN 3 Powder Metallurgical Cold Work Tool Steel Uddeholm Vanadis 30 is a Co high alloyed powder metallurgy high speed steel corresponding to AISI M3:2 + Co. The high compressive strength, 67 HRC, and good abrasive wear resistance makes Uddeholm V.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Carpenter AerMet® 340 |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum K12® Dual Hardness Steel This is a roll bonded, dual hardness armor plate consisting of a high hardness front side to break up or flatten incoming projectiles while the back side functions to capture the projectile.The comp.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201, 40% Cold Work (UNS S20100) Allegheny Ludlum Type 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201 provides advantages over the 18-8 grades in certain applications. Lower cost manganese an.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201, 60% Cold Work (UNS S20100) Allegheny Ludlum Type 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201 provides advantages over the 18-8 grades in certain applications. Lower cost manganese an.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201L, 60% Cold Work (UNS S20103) Allegheny Ludlum Types 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201L provides advantages over the 18-8 grades in certain applications. Lower cost manganese .. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allvac® Vasco® Greek Ascoloy Specialty Steel, Heat Treatment: 871°C (1600°F) + Age Data provided by Allvac.Applications: Compressor blades, vanes, disks, shafts, wheels, fasteners, gas turbine and jet engine components. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Carlson Nitronic® 30® Austenitic Stainless Steel General DescriptionNitronic 30 is a nitrogen-strengthened austenitic stainless steel developed for applications requiring good aqueous corrosion resistance combined with good resistance to abrasive .. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | 200 HB |
Assab Steels 760 Machinery Steel ASSAB 760 is an easily machinable carbon steel characterized by: Good machinabilityGood mechanical strengthASSAB 760 is primarily intended to be used in the as-delivered condition. It is only to be .. |
|||
Density | 7.86 g/cc @Temperature 600 °C |
0.284 lb/in³ @Temperature 1110 °F |
soft annealed condition |
Assab Steels ASP 30 Cold Work Steel ASP 30 is a W-Mo-v-Co alloyed PM high speed steel characterized by:High wear resistanceHigh compressive strength at high hardnessGood through hardening propertiesGood toughnessGood dimensional stabi.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201, 20% Cold Work (UNS S20100) Allegheny Ludlum Type 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201 provides advantages over the 18-8 grades in certain applications. Lower cost manganese an.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201, 30% Cold Work (UNS S20100) Allegheny Ludlum Type 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201 provides advantages over the 18-8 grades in certain applications. Lower cost manganese an.. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
ATI Allegheny Ludlum Stainless Steel Type 201L, 30% Cold Work (UNS S20103) Allegheny Ludlum Types 201 and 201L have the greatest tonnage of the Cr-Ni-Mn steels (200 series). Type 201L provides advantages over the 18-8 grades in certain applications. Lower cost manganese .. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Latrobe LSS™ L6 Tool Steel (ASTM L6) TLS L6 tool steel is a versatile, oil-hardening tool steel that is characterized by very good toughness. TLS L6 tool steel is suitable for use as tools, dies, and machine parts which require a good .. |
|||
Density | 7.86 g/cc | 0.284 lb/in³ | |
Latrobe LSS™ P20 Mold Steel (ASTM P20) TLS P20 mold steel is a versatile, low-alloy tool steel that is characterized by good toughness at moderate strength levels. The steel is commonly used for plastic injection mold cavities and toolin.. |