Quadrant EPP TIVAR® 1000 ASTL PE-UHMW + specific additives (ISO Data)

Category	Polymer , Thermoplastic , Polyethylene (PE) , HDPE , High Density Polyethylene (HDPE), UHMW PE Ultra High Molecular Weight
Manufacturer	Quadrant Engineering Plastics Products
Trade Name	TIVAR®
Port	Ningbo port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Quadrant EPP TIVAR® 1000 ASTL PE-UHMW + specific additives (ISO Data).pdf
Price	EMAIL US sales@lookpolymers.com
	Online Service lookpolymers 27660005

Material Notes:

TIVAR 1000 ASTL, based on a PE-UHMW grade with extremely high molecular weight, has been specifically developed for tough anti-abrasion applications. TIVAR 1000 ASTL shows a higher wear and abrasion resistance and a lower surface resistivity than TIVAR 1000 antistatic. The additives used also render this material static dissipative and highly UV-resistant. Very good wear and abrasion resistance High impact strength, even at low temperatures (particularly UHMW-PE) Excellent chemical resistance Low coefficient of friction Excellent release properties Very low water absorption Moderate mechanical strength, stiffness and creep resistance Very good electrical insulating and dielectric properties (except static dissipative grades) Excellent machinability Physiologically inert (several grades are suitable for food contact) Good resistance to high energy radiation (gamma- and X-rays) Not self-extinguishing

Physical Properties	Metric	English	Comments
Density	0.950 g/cc	0.0343 lb/in³	ISO 1183-1
Water Absorption	<= 0.10 %	<= 0.10 %	96 hr; ISO 62
Moisture Absorption at Equilibrium	<= 0.10 %	<= 0.10 %	50% RH
Water Absorption at Saturation	<= 0.10 %	<= 0.10 %	ISO 62
Outgassing - Total Mass Loss	0.14 %	0.14 %

Mechanical Properties	Metric	English	Comments
Hardness, Shore D	61	61
Ball Indentation Hardness	34.0 MPa	4930 psi	ISO 2039-1
Tensile Strength	21.0 MPa	3050 psi	at Yield; ISO 527-1/-2
Elongation at Break	>= 50 %	>= 50 %	ISO 527-1/-2
Elongation at Yield	15 %	15 %	ISO 527-1/-2
Tensile Modulus	0.800 GPa	116 ksi	ISO 527-1/-2
Flexural Strength	19.0 MPa	2760 psi
Compressive Strength	7.00 MPa @Strain 1 %	1020 psi @Strain 1 %	ISO 604
	11.5 MPa @Strain 2 %	1670 psi @Strain 2 %	ISO 604
	18.0 MPa @Strain 5 %	2610 psi @Strain 5 %	ISO 604
K Factor (ISO)	6.0 µm/km	6.0 µm/km
Charpy Impact Unnotched	NB	NB	ISO 179-1/1eU
Charpy Impact, Notched	9.00 J/cm²	42.8 ft-lb/in²	Partial Break; ISO 179-1/1eA
Coefficient of Friction, Dynamic	0.15 - 0.30	0.15 - 0.30
Sand Slurry	85	85
Limiting Pressure Velocity	0.0500 MPa-m/sec	1430 psi-ft/min	at 1 m/s unlubricated
	0.0800 MPa-m/sec	2280 psi-ft/min	at 0.1 m/s unlubricated

Thermal Properties	Metric	English	Comments
CTE, linear	200 µm/m-°C @Temperature 23.0 - 100 °C	111 µin/in-°F @Temperature 73.4 - 212 °F
Thermal Conductivity	0.400 W/m-K	2.78 BTU-in/hr-ft²-°F
Melting Point	135 °C	275 °F	DSC, 10°C/min.; ISO 11357-1/-3
Maximum Service Temperature, Air	80.0 °C	176 °F	Continuous
Deflection Temperature at 1.8 MPa (264 psi)	42.0 °C	108 °F	ISO 75-1/-2
Flammability, UL94	HB	HB
Oxygen Index	<= 20 %	<= 20 %	ISO 4589-1/-2

Electrical Properties	Metric	English	Comments
Surface Resistivity per Square	<= 1.0e+6 ohm	<= 1.0e+6 ohm	IEC 60093

Compliance Properties	Metric	English
3A-Dairy	No	No
European Food 1935/2004	Yes	Yes
FDA	No	No
USP Class VI	No	No

Chemical Resistance Properties	Metric	English
Acids, Strong (pH 1-3)	Acceptable	Acceptable
Acids, Weak	Acceptable	Acceptable
Alcohols	Acceptable	Acceptable
Alkalies, Strong (pH 11-14)	Acceptable	Acceptable
Alkalies, Weak	Acceptable	Acceptable
Chlorinated Solvents	Acceptable	Acceptable
Conductive / Static Dissipative	Yes	Yes
Continuous Sunlight	Limited	Limited
Hot Water / Steam	Unacceptable	Unacceptable
Hydrocarbons - Aliphatic	Acceptable	Acceptable
Hydrocarbons - Aromatic	Limited	Limited
Inorganic Salt Solutions	Acceptable	Acceptable
Ketones, Esters	Acceptable	Acceptable

Users viewing this material also viewed the following: