Processing Properties | Metric | English | Comments |
---|---|---|---|
Cure Time | 60.0 min | 1.00 hour | On steel (fixture) |
ND Industries StudGrade® 137 Permanent HT Threadlocker General DescriptionHigh strength, high temperature threadlockers for heavy duty applications. Suitable for most applications where disassembly is not required. |
|||
Cure Time | 60.0 min @Temperature 152 °C |
1.00 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 20 PHR Tricresyl Phosphate MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 10 PHR N220 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 120 PHR N774 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 60 PHR N650 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 152 °C |
1.00 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 20 PHR Tricresyl Phosphate MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 120 PHR N339 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 30 PHR N330 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 45 PHR N650 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 90 PHR N339 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 150 °C |
1.00 hour @Temperature 302 °F |
+ 275°C, Minimum, Pre-Bake |
Epoxy Technology EPO-TEK® TV1002 Polyimide Adhesive Material Description: A single component, screen printable polyimide adhesive designed for semiconductor wafer passivation applications. It is a high temperature chemistry capable of resisting >400.. |
|||
Cure Time | 60.0 - 90.0 min | 1.00 - 1.50 hour | Hard Dry |
3M Scotchkote™ XF 895 Fast Curing Floor Coating Scotchkote Fast Curing Floor Coating XF 895 has been specifically developed as a high build floor protection system for application to concrete surfaces, to provide rapid return to serviceProduct Fe.. |
|||
Cure Time | 60.0 min | 1.00 hour | Full, 10 g. 1/4" thick @ RT |
3M Scotch-Weld™ DP600 Concrete Repair and Self-Leveling 3M™ Scotch-Weld™ Concrete Repair Self-Leveling DP600 is a gray, rapid setting, two component polyurethane. It is packaged as a 1:1 ratio liquid in a duo-pack cartridge. With the squeeze of a trigg.. |
|||
Cure Time | 60.0 min @Temperature 23.0 °C |
1.00 hour @Temperature 73.4 °F |
|
Aremco Aremco-Bond™ 807 High Performance Epoxide 10 Minute Set, Non-Sagging, 1:1, Excellent Electrical & Mechanical Properties |
|||
Cure Time | 60.0 min @Temperature 232 °C |
1.00 hour @Temperature 450 °F |
Adequate ventilation is required when curing these products. Outgassing will occur above 300°F and cease after 750°F. An additional 30 minutes is required at the highest service temperature if service temperature is below 750°F. |
Aremco Corr-Paint™ CP4060 High Temperature Protective Coating Silicone, Aluminum Filled This silicone-based, heat resistant coatings are formulated using a state-of-the-art, VOC-compliant, water-dispersible silicone resin. CP4000 adheres to metals, ceramics, refractories, and quartz, a.. |
|||
Cure Time | 60.0 min @Temperature 232 °C |
1.00 hour @Temperature 450 °F |
|
Aremco Corr-Paint™ CP4060-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | >= 60.0 min | >= 1.00 hour | Air Set prior to curing |
Aremco Corr-Paint™ CP4060-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | >= 60.0 min @Temperature 75.0 °C |
>= 1.00 hour @Temperature 167 °F |
tack free |
ACC EP RAP 60 EPI Engineered Polymers Aliphatic Polyurea EP RAP 60 Aliphatic Polyurea, “Powered by Reactamine® Technology”, is a two component 100% solids, no VOC, coating (silicone optional) developed for UV stable (colorfast) polyurea flooring applic.. |
|||
Cure Time | >= 60.0 min | >= 1.00 hour | Air Set prior to curing |
Aremco Cerama-Dip™ 538-N-GRN High Temperature Specialty Ceramic-Inorganic Coating Low viscosity, light gray coating for powder resistors and rheostats to 2600°F (1427°C). black and green pigments also available. |
|||
Cure Time | >= 60.0 min | >= 1.00 hour | Air Set prior to curing |
Aremco Corr-Paint™ CP4020-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | 60.0 min @Temperature 232 °C |
1.00 hour @Temperature 450 °F |
|
Aremco Corr-Paint™ CP4090-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | 60.0 min @Temperature 232 °C |
1.00 hour @Temperature 450 °F |
Adequate ventilation is required when curing these products. Outgassing will occur above 300°F and cease after 750°F. An additional 30 minutes is required at the highest service temperature if service temperature is below 750°F. |
Aremco Corr-Paint™ CP4095 High Temperature Protective Coating Silicone, Aluminum Filled This silicone-based, heat resistant coatings are formulated using a state-of-the-art, VOC-compliant, water-dispersible silicone resin. CP4000 adheres to metals, ceramics, refractories, and quartz, a.. |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 75 PHR N990 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |
|||
Cure Time | 60.0 min @Temperature 150 °C |
1.00 hour @Temperature 302 °F |
|
Dow Corning EG-6301 Two-part, transparent, high modulus (hard) LED encapsulant with high transparency and very long working time.Information provided by Dow Corning |
|||
Cure Time | 60.0 min @Temperature 142 °C |
1.00 hour @Temperature 287 °F |
|
TSE Industries Millathane® CM Millable Polyether Urethane Rubber with 10 PHR N330 Filler MILLATHANE CM is a sulfur and peroxide curable polyether urethane rubber. Its outstanding property is its great resistance to abrasion, which makes it of special interest for articles that are subje.. |